Media Library / Images

TWD-W coupling seal

NBR white

HD 100 C NEON, HD 10 C sensing hose

Type HD-C, aviation hose

Type PCS 38 (Polypal Clean DN 38 mm)

Elaflex nozzles, hose assemblies and Rubber Expansion Joints for petroleum based products

LBS 75 hose assembly for foodstuffs, FDA conform

with VC 50 SS male coupling, Spannloc clamps

Ship loading/unloading various media - STW 150 and UTS 150 hose assemblies

ZVA Slimline 2 GR

with red scuffguard; CSB 21 Coax Safety Break with BS 21 Break Sleeve; Slimline COAX hose assembly

ZVA Slimline 2, black, guard 3 - side/front view

AVKC 50 Ms

'Camlock' brass steel male part to EN 14420 - 7 with hose tail and Spannloc clamps

ZVF 50 JET for aircraft refuelling

with EA 951 PTL black, SC 50 Al, HD 50 C and BD 50

DEC – Dry Evotek Couplings:

dry disconnect couplings for the chemical industry.
• Low connecting forces even against pressure
• Ergonomic handle (DN40 and bigger)
• Good transmission ratio in the cam curve
• Wide range of chemical resistance due to selection of high quality materials
• Minimized spillage during decoupling

ZVG 2 ACME nozzle for L.P. Gas / Autogas

LPG nozzle for vehicle refuelling with liquefied petroleum gas (propane, butane and mixtures) up to 50 l / min. Working pressure 25 bar. Test pressure 40 bar. Burst pressure > 100 bar. Temperature range - 25° up to + 70° C, 'LT'-Type down to - 40° C.

ERV-G

"Yellow Band" Rubber Expansion Joints for L.P. Gas; pumping station at tank storage

GasGuard LPG nozzle GG30

LPGas nozzle with Bayonet connection according to EN 12806 - 2003 for the filling of commercial and passenger Autogas vehicles as well as mobile and small stationary storage tanks with propane and butane. New : 4-slot design to facilitate connection of the nozzle to the vehicle fill point. New nose piece design to reduce the released gas upon valve closure, incorporating improved gas release method to minimise the risk of splash back.

MannTek DGC DryGasCouplings for L.P. Gas

DGC-M 50 F, DGC-M 80-3", DGC-M 50-2", LPG hose

LPG Autogas dispenser, ZVG 2 ACME nozzle, LPG 16 dispensing hose

V 16-3/4"

Male ferrule hose coupling EN 14424, reusable. Slimline 16 hose, green.

RS 2 x 2 Ms

Reducer Female/Male

Oasis NC 103-200 Bus & Truck Nozzle

ARK 19 Safety Break including BS 19 Break Sleeve

Safety Break (Hose Break) for installation to LPG Autogas dispensers. Reassembly on site without tools

GasGuard LPG nozzles

GG1E, GG1DN, GG20H, GG30

Road tanker reel with HD 50 hose assembly, ZV 500 nozzle

ERV Rubber Expansion Joints

Picture 2

DCC Dry Cryogenic Coupling for LNG

Coupling process

ElaSil® Silicone hose assemblies DN 13-102

For for high media purity requirements, easy to clean. Suitable for Pharma, foodstuff and cosmetics industry. Homogeneous hose construction of platinum cured, translucent and phtalate free Silicone (FDA / USP), resistant to kinking and highly flexible. Large temperature range -60° C to +200° C. Available as complete hose assembly with crimped fittings, DN 13 to 102. Here: DN 25 with Camlock Cam Locking Coupling and Triclamp connection

ZVG 2 ACME nozzle for L.P. Gas / Autogas

pulling lever and latching, possible with one hand

GasGuard LPG nozzle GG1E

eoconomic type for industrial refueling / attended refueling. Release volume on valve closure: 1,9 cm³.

Movable Storage Hose Reel with manual rewind system white, HD 38, ZV 400

customised

AMKX 50 SS

'Camlock' stainless steel steel coupler to EN 14420 - 7 with hose tail and Spannfix clamps

Elaflon PTFE 38 hose assembly with crimped fitting